HUAWEI Industrial Network Switch S6720-54C-EI-48S-AC

$7,600.00

United States dollar ($) - USD
  • United States dollar ($) - USD
  • Euro (€) - EUR
Categories: , Tags: , ,

Description

Version Mapping

Table 4-145 lists the mapping between the S6720-54C-EI-48S-AC chassis and software versions.

Table 4-145 Version mapping

Series Model Software Version
S6720-EI S6720-54C-EI-48S-AC V200R008C00 to V200R023C00 versions

NOTE:

V200R021C01 is not supported.

Appearance and Structure

Figure 4-62 S6720-54C-EI-48S-AC appearance
1 Forty-eight 10GE SFP+ ports

Applicable modules and cables:

2 Two 40GE QSFP+ ports

Applicable modules and cables:

NOTE:

A 40GE QSFP+ optical port can be split into four 10GE ports.

3 One ETH management port 4 One console port
5 One USB port 6 Ground screw

NOTE:

It is used with a ground cable.
7 ESN label

NOTE:

You can draw it out to view the ESN and MAC address of the switch.

8 Rear card slot

NOTE:

Card supported:

9 Fan slot

10 Power module slot 2

NOTE:

Applicable power modules:

11 Power module slot 1

NOTE:

Applicable power modules:

Port Description

10GE SFP+ port

A 10GE SFP+ Ethernet optical port supports auto-sensing to 1000 Mbit/s. It sends and receives service data at 1000 Mbit/s or 10 Gbit/s. Table 4-146 describes the attributes of a 10GE SFP+ Ethernet optical port.

Table 4-146 Attributes of a 10GE SFP+ port

Attribute

Description

Connector type

LC/PC

Optical port attributes

Depend on the optical module used

Standards compliance

IEEE802.3ae

Working mode

GE/10GE auto-sensing

40GE QSFP+ port

A 40GE QSFP+ optical port sends and receives service traffic at 40 Gbit/s and can be split into four 10GE ports. After a split, the 40GE QSFP+ optical port needs to be connected to a remote device using a 1-to-4 QSFP+ fiber (with matching optical modules), a 1-to-4 QSFP+ AOC cable, or a 1-to-4 QSFP+ copper cable. Table 4-147 describes the attributes of a 40GE QSFP+ optical port.

Table 4-147 Attributes of a 40GE QSFP+ optical port

Attribute

Description

Connector type

MPO/LC

Optical port attributes

Depend on the optical module used

Standards compliance

IEEE802.3ba

Console port

The console port is connected to a console for on-site configuration. The port must use a console cable. The console port is used when a switch is powered on for the first time. For details about the attributes of a console port, see Table 4-148.

Table 4-148 Attributes of a console port

Attribute

Description

Connector type

RJ45

Standards compliance

RS-232

Working mode

Duplex Universal Asynchronous Receiver/Transmitter (UART)

Baud rate

9600 bit/s, 19200 bit/s, 38400 bit/s, 57600 bit/s, or 115200 bit/s

Default value: 9600 bit/s

ETH management port

You can connect a switch to a configuration terminal or network management workstation through the ETH management port to configure the switch locally or remotely. The port must use an Ethernet cable. You can choose to download the software package through the ETH management port in the BootLoad menu. File transfer through the ETH management port is faster than transfer through the console port. Table 4-149 describes the attributes of an ETH management port.

Table 4-149 Attributes of an ETH management port

Attribute

Description

Connector type

RJ45

Standards compliance

IEEE802.3

Working mode

10/100 Mbit/s auto-sensing

Maximum transmission distance

100 m

In V200R012C00 and later versions, you can log in to the switch that contains the ETH management port for the first time through the ETH port. For details, see “First Login to a Switch” in the Configuration Guide – Basic Configuration. If you have logged in to the device for the first time by pressing and holding the MODE button for 6 seconds or longer and saved the configuration, the default configuration on the ETH port will be cleared. In this case, you cannot log in to the switch for the first time through the ETH port. You are advised to log in to the switch for the first time through the ETH port.

USB port

The USB port can have a USB flash drive connected to upgrade the switch, or transfer configuration files or other files. The USB port can only connect to a USB flash drive that complies with USB 2.0.

Reviews

There are no reviews yet.

Be the first to review “HUAWEI Industrial Network Switch S6720-54C-EI-48S-AC”